Plaster & Wood Range Hood Cover- Reveal

When dreaming up our kitchen from bare studs, I knew I wanted a custom vent hood featuring plaster and a raw wood beam. I loved the idea of the plaster feeling very old world and European while the raw wood would add a rustic element to our kitchen. 

I came across Brooke and Henry's blog post here about building your own plaster hood. This article was very helpful and eye opening in the fact that really you're building beauty around the vent itself. I'm not sure why- but I thought custom vent hoods were elaborate (and yes there are some) and confusing, haha? I loved that this article broke down how they built the framing beneath the plaster. 

After some more digging, I came up with rough measurements of the 2x6" structure. Our hood is a little different from theirs as I wanted the side panels to also have an arch to match the front arch swoop. I built three tiers of 2x6" rectangles- each one being a bit smaller than the last for the effect of the swoop on front and sides. (Pictured below I just have the top and bottom rectangle screwed into the wall framing.)

After reading about average counter to hood heights (ranging anywhere from 30-35"?) I settled on about 30" for my bottom rectangle piece. Once I had all our structure pieces screwed into the studs- unlike Brooke and Henry'swe cut a very thin plywood (if I'm remembering correctly it was close to 1/4"?) to the shape of the side and screwed that into our rectangular structure. The key is to have a thin enough plywood so that your wood bends for the swoop. I do remember it being a bit more difficult to push the wood shell into the rectangle framing. You'll want long wood screws to really hold the panel pieces to your 2x6" framing.

After some trial and error, we were able to get our shapes pretty well close to what I was envisioning. I knew it didn't have to be perfect since we were covering the panels in plaster and the raw beam would cover the bottom.

 I found this vent hood from Wayfair. It had great reviews while being pretty affordable and seamless. Underneath, we built a frame so that the vent hood had something to screw into. 

I found an old barn beam at Keim Lumber (a local hardware) several years ago for my birthday. We had to rip the beam down into three long slabs- of course using one of the outside hand hewn pieces for the front of the hood vent. For the plaster, I mixed up a quarter bag of Surecrete. I have a tutorial on YouTube on how I used this product in the shoppe. I love using this top coat concrete because it's easy to apply and dries a nice, white texture- not to mention it also hid all our poor cutting imperfections, haha.

 Applying the concrete over the plywood was very simple and took over just an hour to do. Drumroll for the final reveal, please...

 I love the look of the plaster/concrete mixed with the raw beam. I can't wait to finish our tile backsplash now! We plan to seal the concrete and raw beam so that stove oils don't ruin anything over the years. 

I hope this pretty easy DIY project inspires you to dream up your own custom hood vent! 

Hugs, Alyssa

JUNE 2022- 95% Finished:



  • Cottonwood

    I take a lint-free cloth, that is slightly damp and rub over it. It’s not bad to clean… however, I would probably have sealed the hood with a matte poly for even more of an easier clean!

  • Elizabeth

    I see lots of questions about the ability to clean this, but no replies. I have the same question. Please reply as to the clean ability?

  • Shannon

    I am wondering how easy it is to clean? I’d like to do something similar but want to be sure I can maintain it easily. Its lovely, by the way!

  • Kendra

    I love this design and am currently in the construction phase of our new kitchen. We plan to have a 36-gas range, would you recommend the 30-inch vent insert as you mentioned above, or was that for a 30-inch range? I wasn’t sure about the size of your range as shown. Thanks!

  • Xina

    What size of wood beam did you use? Did you need to seal it? Such a beautiful timeless look😍

Leave a comment

Please note, comments must be approved before they are published

    1 out of ...